500
Series Deck Drain
The POLYCAST® 500 Series Deck Drain System
is ideally suited for a variety of above grade applications requiring
drainage of incidental water run-off. The 500 Series is Strongwell’s
shallowest drain, measuring: O.D. 48” x 6.25” x 2.5” and
I.D. of 48” x 4.25” x 1.75”. It is designed to
be installed in suspended slab applications such as parking structures,
pool deck areas and many other thin slab applications. The precast
sections are made up of 4’ lengths. Each section has a 4” bottom
cut-out for pipe connections. Gratings available for this system
are the slotted galvanized and stainless steel grates, part numbers
DGO640 and DGO647, and fiberglass grates, part number DGO644.
POLYCAST® 500 Series is available in
either polyester or Vinyl Ester polymer concrete. The polyester
polymer concrete would be used for most drainage applications.
Vinyl ester polymer concrete is used for high corrosive and high
temperature applications. The 500 Series drains are designed for
pneumatic tire traffic only. For added depth and/or solid tire
forklift (full traffic) applications, the 700 Series (HARDNOSE)
frame can be added. Grating hold-down device DAO542 is recommended.
600
Series Presloped Heavy Duty/Light Duty
The POLYCAST® 600 Series Presloped System
is ideally suited for a variety of commercial and industrial applications.
It is designed to have flow rates equal to, or greater
than, most larger poured-in-place trench drains. With
the proper components, flow rates of 470 GPM per outlet are attainable.
The precast trench sections and grates are made up of 2’ and
4’ lengths. Certain 4’ channels and all half channels
have 4” and 6” bottom cut-outs for pipe connections.
POLYCAST® 600 Series is available in
either polyester or vinyl ester polymer concrete. The polyester
polymer concrete is used for most drainage applications. Vinyl
ester polymer concrete is used for high corrosive and high temperature
applications. The 600 Series Drains are designed for pneumatic
tire traffic only.
800 Series MAXI
Heavy Duty
The POLYCAST® 800 Series Channel
is designed for those high volume situations that exceed the
capacity of the POLYCAST® 600 Series. The channel, with
a width of 12”, is approximately double the width of
the standard 600 Series channels. The 825 Section is a neutral
channel with interlocking tongue-and-groove joints. The 825
channel is designed for areas of high volume cross-flow interception,
or areas where the larger cross-section is necessary. Channels
can also be used as a corrosion resistant, secondary containment
system.
The 825 channel is available in either
polyester or vinyl ester polymer concrete. The polyester polymer
concrete is used for most drainage applications; the Vinyl
Ester polymer concrete should be used for highly corrosive
situations or higher temperature applications. All POLYCAST® 800
Series gratings, except the fiberglass grating, are 2’ long
with two gratings required for the 4’ channel. The fiberglass
grate is 4’ in length. The iron gratings and covers for
the 825 channel come with locking bolts. The bolts fit threaded
inserts in the channel bearing ledges. The bolts are recessed
to fit below the grating surface. Three different end caps
are available for the 825 channel. The closed end cap is designed
to fit either end of the channel. Drain end caps fit the downstream
end and can be ordered with a 6” or 8” pipe stub.
The flow rate of the 825 channel varies with the slope of the
installation. The 825 channel is not presloped and any slope
required should be designed into the slab.
POLYCAST® 3000
Series
POLYCAST® 3000 Series High Capacity Drain System
is designed for airports, roadways and other applications needing high
volume flow rates. The flow rate for this system is more than 3,000
gallons per minute for 120' of drain. The system channels are manufactured
using the pultrusion process to produce a lightweight, high strength
fiber reinforced polymer composite channel.
Residential 
